Location:Home >NO: GTI-GS Information

GFRP Flat Sheet
Model NO: GTI-GS
Introduction:


We accept customization of FRP pultruded profiles according to the following requirements.

●Product section:
Be able to produce FRP pultruded profiles with any cross-section

●Color:
According to your customization. We can supply FRP profiles with various colors

●Resin matrix:
The appropriate use of resin formulations is according to the operation environment of final product and usage requirement (see media properties).
The resins used in pultrusion process are mainly general purpose resin, isophthalic resin o-benzene resin, Vinyl Ester Resins, and phenolic resins.

●Reinforced materials:
It is the support frame of glass steel which largely determines the mechanical strength and elastic modulus of pultruded products.
The reinforced materials used in pultrusion process are mainly glass fiber roving , glass fiber mat and glass fiber fabrics.


We accept customization of FRP pultruded profiles according to the following requirements.

●Product section:
Be able to produce FRP pultruded profiles with any cross-section

●Color:
According to your customization. We can supply FRP profiles with various colors

●Resin matrix:
The appropriate use of resin formulations is according to the operation environment of final product and usage requirement (see media properties).
The resins used in pultrusion process are mainly general purpose resin, isophthalic resin o-benzene resin, Vinyl Ester Resins, and phenolic resins.

●Reinforced materials:
It is the support frame of glass steel which largely determines the mechanical strength and elastic modulus of pultruded products.
The reinforced materials used in pultrusion process are mainly glass fiber roving , glass fiber mat and glass fiber fabrics.

Specification
Model No. A B
GTI-GS23050 23 5
GTI-GS27250 27.2 5
GTI-GS29005 29 0.5
GTI-GS30051 30 5.1
GTI-GS40060 40 6
GTI-GS42060 42 6
GTI-GS46042 46 4.2
GTI-GS49747 49.7 4.7
GTI-GS50213 50.2 1.3
GTI-GS61513 61.5 1.3
GTI-GS64265 64.2 6.5
GTI-GS65041 65 4.1
GTI-GS20050 200 5

Pultrusion Products

Fibre bundles and slit fabrics are pulled through a wet bath of resin and formed into the rough part shape. Saturated material is extruded from a heated closed die curing while being continuously pulled through die. Some of the end products of the pultrusion process are structural shapes, i.e. I beam, angle, channel and flat sheet. These materials can be used to create all sorts of fibreglass structures such as ladders, platforms, handrail systems tank, pipe and pump supports.

Mechanical Properties Related Standards Unit Measured Longitudinally
Standard Shapes Rod & Square Bar
Tensile Strength ASTM D 638 psi 30000 100000
Tensile Modulus ASTM D 638 psi 2.3X106 6.0X106
Flexural Strength ASTM D 790 psi 30000 100000
Flexural Modulus ASTM D 790 psi 1.8X106 6.0X106
Compressive Strength ASTM D 695 psi 30000 600000
Compressive Modulus psi 2.3X106 6.0X106
Izod Impact Strength FT.-LBS./IN 25 40
Barcol Hardness 50 50
Electrical Properties 50 50
Dielectric strength ASTM D 149 VPM,min 200*** 150
Dielectric strength 1" long specimen tested parallel to laminate face shorttime in oil
KV per inch 40 70
(24 hrs. exposure)% by weight 0.75 0.75
Coeffecient of thermal 5.2X106 5.2X106
views: 2861